Currently running OPNsense on a small Dual-Nic Shuttle PC with an Pentium G4560 and 4 gigs of ram and it’s been handling everything I throw at it perfectly fine. Ive got 16 Interfaces, around 10 Wireguard Peers and a SIT tunnel to HE and Im still getting Line Speeds through the firewall.

a minipc with 2 nics running proxmox with opnsense as a vm and one of the nics passed through. that way I can use it for more stuff.

https://lemmy.world/post/48913927/24549697

A used Lenovo ThinkCentre Tiny M720q mini PC, with the PCIe riser and an Intel chipset (Huawei) dual-10 Gbit NIC, running a pretty basic install of OpenWrt. Has no issue with 10 Gbit throughput, maxes out at about maybe 12 Gbit if you do a full duplex test, which I think may be a limitation of the limited PCIe lanes in the riser.

I got 10 Gbit internet at home, looked at the prices of 10 Gbit routers and noted right out! Built this for maybe $100 in stuff off of auctions.

A fanless thin client with Opnsense and a four-port Intel NIC.

HP Prodesk with some i5 8th gen running proxmox and with a 4x 1gb pcie nic on which a opnsense vm runs.

My DNS was done through pihole. Transitioned now to technitium-dns.

My personal blocklist(s):
https://github.com/Appoxo/Ad-Spam-Blocklist
Contains a list for opnsense (IPs) and technitium-dns (but pihole should be compatible).
Anything else should be mentioned in the readme.

In case of questions, feel free to ask.

I run some china box with 5 integrated 2.5GBe NICs, 48GB RAM and 2x 500GB SSD/NVMe. CPU is Celeron® 6305 @ 1.80GHz, two cores or HT, who knows…

On this I run Proxmox. I didn’t like Proxmox integrated firewall, so I rolled my own.

all containers unprivileged

one container is the firewall. it has all up+down stream NICs mapped via bridges, cable internet, backup 5g internet on dedicated ports. one port to the switch with a few VLANs, and one bridge that is local to the Proxmox for the local VLANs.

Every service I operate sits in its own network/segment, usually with a /30 netmask. VMs/containers have a eth0 device in this and the firewall defined as default gw. On the firewall the VLAN interfaces are named as the container/service. So the interfaces are not eth0 but wan, wan5g, frigate etc. Great for readability.

Some networks like “family” or “guest” or the one with the APs/WLAN-controller are /24. Bit big, but what ever.

I have a structured netfilter firewall script, fw.sh calling it’s parts under fw.d/*fw. Each service is managed individually, sometimes widely open (iptables -A FORWARD -i frigate -o wan* -j ACCEPT) but usually down to the required ports. Database, reverse proxy etc all on separate containers.

There is also like 30 VPN configs from 2 VPN providers. I have a home assistant dashboard where I can direct specific devices to use specifig VPNs. My webradio is routed via UK so I can enjoy BBC2.

root@mercury:~# ip rule show
0:      from all lookup local
20:     from all lookup main suppress_prefixlength 1
300:    from XXX lookup wan_table
310:    from XXX lookup wan5g_table
1000:   from all fwmark 0x1 lookup bbc-ss-lon
1001:   from all fwmark 0x1 lookup bbc-ss-man
3000:   from XXX lookup pm-gb
4000:   from all lookup wan_table
5000:   from all lookup wan_table
5100:   from all lookup wan5g_table
32766:  from all lookup main
32767:  from all lookup default

ip rule also does the fail over to wan5g if required. There are some rules where I tried to auto-filter BBC traffic with marked connections via dnsmasq, but BBC knows all my VPNs (not BBC radio it seems).

IPSec VPNs and other OpenVPNs (dialup, site2site) are handled via a dedicated LXC. There is a tor entry node container, for a few services and one of the public WLANs. Firewall makes sure certain traffic can only exit via certain upstream interfaces, vpn*, wan, wan*… very helpful

I didn’t like opensense… don’t know why. Work a lot with firewalls in my job (mainly check point, fortigate) so have some professional background.

Also: client isolated WiFi for all iot shit. No internet for TV (jellyfin), PV controllers and most others.

I’m running pfsense with wireguard site to site connection between 2 locations. Vlan for my mqtt for my meshtastic. I did have an ad blocker on it but I found it wasn’t very good. It was blocking too many things.

Switched to Adguard on my Proxmox instead.

deleted by creator

I build a Linux system with multiple NICs. It’s heavyweight for a router, and probably not very efficient, but it does the job very well and I love it. I’m using foomuuri to manage the NFTables and NAT and it was very easy (although it’s a very obscure piece of software and the documentation and community isn’t excessively comprehensive, you might have better luck with something more common but it works nicely for me). It can pull in all the adblocking lists and all that fun stuff. I find it pretty intuitive to configure, at least compared to the horrors of most networking/routing configuration nonsense.

For DHCP I tried using the ISC’s new “kea” in the hopes it would be modern and clean alternative to the venerable old isc-dhcp-server but it turned out to be a horrible mistake. They made some awful, insane, unjustifiable design decisions in that software. It gets confused about IP addresses already being claimed (by the exact same host/MAC) address because some arbitrary value changed in how it identifies itself, and then does absurd things with static leases, it just randomly decides to give it a dynamic lease instead, and then will fixate on that dynamic lease and never let it have the static lease back, I fought with it for months, it kept breaking my network for absolutely no reason and it was a nightmare.

Back to trusty old isc-dhcp-server for me. And of course bind for DNS, I’m a bit old-school but it’s very comfortable.

dnsmasq might be a lighter-weight and easier alternative you could consider, I think it does DHCP as well, convenient.

And of course, being a full Linux server means you can put all kinds of other stuff on it too. Stuff that needs to be both publicly visible and privately visible on the LAN seems like an obvious fit, but in fact it’s probably the worst place to put those services, because you run into issues with NAT hairpinning and other nonsense. For services that are strictly intended for the private LAN/VPN, or services that are strictly public facing, it can handle those just fine by restricting them to a specific interface. But you should avoid stuff that needs to listen on both sides of the connection, it can be done, but it’s tricky and annoying and not ideal.

If you need both internal and external access, port-forwarding from the outside through the NAT to another dedicated internal host is a much better solution if possible, it’s still a bit tricky (you may have to override the DNS for that domain internally to use the private IP instead of the public one) but it’s quite reliable and functional once you have it set up.

None of this is really for the faint of heart, it’ll likely require a fair bit of trial and error and physical access to the machine to resolve issues. But it’s a fun project and I think the end result is worth it.

Opnsense on whatever. Plus pihole for DNS/adblock.

I was using an N100 based mini PC and it did fine at 1gbit. But now that I have 3, and it’s realistically closer to 4 or 5 it doesn’t cut the mustard.

Proper hardware based routers are also just so much more efficient. That N100 machine was constantly hot to the touch. My new UniFi router uses less power and does 10 gig easily.

I usually just use proper network devices. OpenWRT will generally run on anything with Mediatec or Qualcomm based assuming it has support

I used to run opnsense on a Xeon blade in my old C6100. It worked well enough but was a waste. Now it’s just a stock ER605 without the Omada controller.

I bought a firewall appliance based on an Intel CPU, with 4x 2.5gbps Ethernet ports, 8gb ram. Installed opnSense on it and been super happy even since!

A bit pricey the hardware, but it’s been totally rock solid for almost two years now.

I have configured unbound with ad blocking on opnSense, and it has every single option I would ever want on it. Amazing stuff.